Basic Commands ************** The following sections discuss commands common to all the routing daemons. Config Commands =============== In a config file, you can write the debugging options, a vty's password, routing daemon configurations, a log file name, and so forth. This information forms the initial command set for a routing beast as it is starting. Config files are generally found in /etc/frr. Each of the daemons has its own config file. The daemon name plus ".conf" is the default config file name. For example, zebra's default config file name is "zebra.conf". You can specify a config file using the "-f" or "--config_file" options when starting the daemon. Basic Config Commands --------------------- hostname HOSTNAME Set hostname of the router. [no] password PASSWORD Set password for vty interface. The "no" form of the command deletes the password. If there is no password, a vty won't accept connections. [no] enable password PASSWORD Set enable password. The "no" form of the command deletes the enable password. [no] log trap LEVEL These commands are deprecated and are present only for historical compatibility. The log trap command sets the current logging level for all enabled logging destinations, and it sets the default for all future logging commands that do not specify a level. The normal default logging level is debugging. The "no" form of the command resets the default level for future logging commands to debugging, but it does not change the logging level of existing logging destinations. [no] log stdout LEVEL Enable logging output to stdout. If the optional second argument specifying the logging level is not present, the default logging level (typically debugging) will be used. The "no" form of the command disables logging to stdout. The "LEVEL" argument must have one of these values: emergencies, alerts, critical, errors, warnings, notifications, informational, or debugging. Note that the existing code logs its most important messages with severity "errors". [no] log file [FILENAME [LEVEL]] If you want to log into a file, please specify "filename" as in this example: log file /var/log/frr/bgpd.log informational If the optional second argument specifying the logging level is not present, the default logging level (typically debugging, but can be changed using the deprecated "log trap" command) will be used. The "no" form of the command disables logging to a file. Note: If you do not configure any file logging, and a daemon crashes due to a signal or an assertion failure, it will attempt to save the crash information in a file named "/var/tmp/frr..crashlog". For security reasons, this will not happen if the file exists already, so it is important to delete the file after reporting the crash information. [no] log syslog [LEVEL] Enable logging output to syslog. If the optional second argument specifying the logging level is not present, the default logging level (typically debugging, but can be changed using the deprecated "log trap" command) will be used. The "no" form of the command disables logging to syslog. [no] log monitor [LEVEL] Enable logging output to vty terminals that have enabled logging using the "terminal monitor" command. By default, monitor logging is enabled at the debugging level, but this command (or the deprecated "log trap" command) can be used to change the monitor logging level. If the optional second argument specifying the logging level is not present, the default logging level (typically debugging) will be used. The "no" form of the command disables logging to terminal monitors. [no] log facility [FACILITY] This command changes the facility used in syslog messages. The default facility is "daemon". The "no" form of the command resets the facility to the default "daemon" facility. [no] log record-priority To include the severity in all messages logged to a file, to stdout, or to a terminal monitor (i.e. anything except syslog), use the "log record-priority" global configuration command. To disable this option, use the "no" form of the command. By default, the severity level is not included in logged messages. Note: some versions of syslogd (including Solaris) can be configured to include the facility and level in the messages emitted. [no] log timestamp precision [(0-6)] This command sets the precision of log message timestamps to the given number of digits after the decimal point. Currently, the value must be in the range 0 to 6 (i.e. the maximum precision is microseconds). To restore the default behavior (1-second accuracy), use the "no" form of the command, or set the precision explicitly to 0. log timestamp precision 3 In this example, the precision is set to provide timestamps with millisecond accuracy. [no] log commands This command enables the logging of all commands typed by a user to all enabled log destinations. The note that logging includes full command lines, including passwords. If the daemon startup option *--command-log-always* is used to start the daemon then this command is turned on by default and cannot be turned off and the [no] form of the command is dissallowed. [no] log-filter WORD [DAEMON] This command forces logs to be filtered on a specific string. A log message will only be printed if it matches on one of the filters in the log-filter table. Can be daemon independent. Note: Log filters help when you need to turn on debugs that cause significant load on the system (enabling certain debugs can bring FRR to a halt). Log filters prevent this but you should still expect a small performance hit due to filtering each of all those logs. log-filter clear [DAEMON] This command clears all current filters in the log-filter table. Can be daemon independent. service password-encryption Encrypt password. service advanced-vty Enable advanced mode VTY. service terminal-length (0-512) Set system wide line configuration. This configuration command applies to all VTY interfaces. line vty Enter vty configuration mode. banner motd default Set default motd string. no banner motd No motd banner string will be printed. exec-timeout MINUTE [SECOND] Set VTY connection timeout value. When only one argument is specified it is used for timeout value in minutes. Optional second argument is used for timeout value in seconds. Default timeout value is 10 minutes. When timeout value is zero, it means no timeout. no exec-timeout Do not perform timeout at all. This command is as same as "exec- timeout 0 0". access-class ACCESS-LIST Restrict vty connections with an access list. Sample Config File ------------------ Below is a sample configuration file for the zebra daemon. ! ! Zebra configuration file ! hostname Router password zebra enable password zebra ! log stdout ! ! "!" and "#" are comment characters. If the first character of the word is one of the comment characters then from the rest of the line forward will be ignored as a comment. password zebra!password If a comment character is not the first character of the word, it's a normal character. So in the above example "!" will not be regarded as a comment and the password is set to "zebra!password". Terminal Mode Commands ====================== write terminal Displays the current configuration to the vty interface. write file Write current configuration to configuration file. configure [terminal] Change to configuration mode. This command is the first step to configuration. terminal length (0-512) Set terminal display length to "(0-512)". If length is 0, no display control is performed. who Show a list of currently connected vty sessions. list List all available commands. show version Show the current version of frr and its build host information. show logging Shows the current configuration of the logging system. This includes the status of all logging destinations. show log-filter Shows the current log filters applied to each daemon. show memory Show information on how much memory is used for which specific things in frr. Output may vary depending on system capabilities but will generally look something like this: frr# show memory System allocator statistics: Total heap allocated: 1584 KiB Holding block headers: 0 bytes Used small blocks: 0 bytes Used ordinary blocks: 1484 KiB Free small blocks: 2096 bytes Free ordinary blocks: 100 KiB Ordinary blocks: 2 Small blocks: 60 Holding blocks: 0 (see system documentation for 'mallinfo' for meaning) --- qmem libfrr --- Buffer : 3 24 72 Buffer data : 1 4120 4120 Host config : 3 (variably sized) 72 Command Tokens : 3427 72 247160 Command Token Text : 2555 (variably sized) 83720 Command Token Help : 2555 (variably sized) 61720 Command Argument : 2 (variably sized) 48 Command Argument Name : 641 (variably sized) 15672 [...] --- qmem Label Manager --- --- qmem zebra --- ZEBRA VRF : 1 912 920 Route Entry : 11 80 968 Static route : 1 192 200 RIB destination : 8 48 448 RIB table info : 4 16 96 Nexthop tracking object : 1 200 200 Zebra Name Space : 1 312 312 --- qmem Table Manager --- To understand system allocator statistics, refer to your system's *mallinfo(3)* man page. Below these statistics, statistics on individual memory allocation types in frr (so-called *MTYPEs*) is printed: * the first column of numbers is the current count of allocations made for the type (the number decreases when items are freed.) * the second column is the size of each item. This is only available if allocations on a type are always made with the same size. * the third column is the total amount of memory allocated for the particular type, including padding applied by malloc. This means that the number may be larger than the first column multiplied by the second. Overhead incurred by malloc's bookkeeping is not included in this, and the column may be missing if system support is not available. When executing this command from "vtysh", each of the daemons' memory usage is printed sequentially. logmsg LEVEL MESSAGE Send a message to all logging destinations that are enabled for messages of the given severity. find COMMAND... This command performs a simple substring search across all defined commands in all modes. As an example, suppose you're in enable mode and can't remember where the command to turn OSPF segment routing on is: frr# find segment-routing on (ospf) segment-routing on The CLI mode is displayed next to each command. In this example, "segment-routing on" is under the *router ospf* mode. Similarly, suppose you want a listing of all commands that contain "l2vpn": frr# find l2vpn (view) show [ip] bgp l2vpn evpn [json] (view) show [ip] bgp l2vpn evpn all [json] (view) show [ip] bgp l2vpn evpn all neighbors A.B.C.D advertised-routes [json] (view) show [ip] bgp l2vpn evpn all neighbors A.B.C.D routes [json] (view) show [ip] bgp l2vpn evpn all overlay ... show thread cpu [r|w|t|e|x] This command displays system run statistics for all the different event types. If no options is specified all different run types are displayed together. Additionally you can ask to look at (r)ead, (w)rite, (t)imer, (e)vent and e(x)ecute thread event types. show thread poll This command displays FRR's poll data. It allows a glimpse into how we are setting each individual fd for the poll command at that point in time. Common Invocation Options ========================= These options apply to all frr daemons. -d, --daemon Run in daemon mode. -f, --config_file Set configuration file name. -h, --help Display this help and exit. -i, --pid_file Upon startup the process identifier of the daemon is written to a file, typically in "/var/run". This file can be used by the init system to implement commands such as ".../init.d/zebra status", ".../init.d/zebra restart" or ".../init.d/zebra stop". The file name is an run-time option rather than a configure-time option so that multiple routing daemons can be run simultaneously. This is useful when using frr to implement a routing looking glass. One machine can be used to collect differing routing views from differing points in the network. -A, --vty_addr
Set the VTY local address to bind to. If set, the VTY socket will only be bound to this address. -P, --vty_port Set the VTY TCP port number. If set to 0 then the TCP VTY sockets will not be opened. -u Set the user and group to run as. -N Set the namespace that the daemon will run in. A "/" will be added to all files that use the statedir. If you have "/var/run/frr" as the default statedir then it will become "/var/run/frr/". -v, --version Print program version. --command-log-always Cause the daemon to always log commands entered to the specified log file. This also makes the *no log commands* command dissallowed. Enabling this is suggested if you have need to track what the operator is doing on this router. --log When initializing the daemon, setup the log to go to either stdout, syslog or to a file. These values will be displayed as part of a show run. Additionally they can be overridden at runtime if desired via the normal log commands. --log-level When initializing the daemon, allow the specification of a default log level at startup from one of the specified levels. --tcli Enable the transactional CLI mode. Loadable Module Support ======================= FRR supports loading extension modules at startup. Loading, reloading or unloading modules at runtime is not supported (yet). To load a module, use the following command line option at daemon startup: -M, --module Load the specified module, optionally passing options to it. If the module name contains a slash (/), it is assumed to be a full pathname to a file to be loaded. If it does not contain a slash, the /usr/lib/frr/modules directory is searched for a module of the given name; first with the daemon name prepended (e.g. "zebra_mod" for "mod"), then without the daemon name prepended. This option is available on all daemons, though some daemons may not have any modules available to be loaded. The SNMP Module --------------- If SNMP is enabled during compile-time and installed as part of the package, the "snmp" module can be loaded for the *Zebra*, *bgpd*, *ospfd*, *ospf6d* and *ripd* daemons. The module ignores any options passed to it. Refer to SNMP Support for information on its usage. The FPM Module -------------- If FPM is enabled during compile-time and installed as part of the package, the "fpm" module can be loaded for the *zebra* daemon. This provides the Forwarding Plane Manager ("FPM") API. The module expects its argument to be either "Netlink" or "protobuf", specifying the encapsulation to use. "Netlink" is the default, and "protobuf" may not be available if the module was built without protobuf support. Refer to zebra FIB push interface for more information. Virtual Terminal Interfaces =========================== VTY -- Virtual Terminal [aka TeletYpe] Interface is a command line interface (CLI) for user interaction with the routing daemon. VTY Overview ------------ VTY stands for Virtual TeletYpe interface. It means you can connect to the daemon via the telnet protocol. To enable a VTY interface, you have to setup a VTY password. If there is no VTY password, one cannot connect to the VTY interface at all. % telnet localhost 2601 Trying 127.0.0.1... Connected to localhost. Escape character is '^]'. Hello, this is |PACKAGE_NAME| (version |PACKAGE_VERSION|) |COPYRIGHT_STR| User Access Verification Password: XXXXX Router> ? enable . . . Turn on privileged commands exit . . . Exit current mode and down to previous mode help . . . Description of the interactive help system list . . . Print command list show . . . Show system inform wh. . . Display who is on a vty Router> enable Password: XXXXX Router# configure terminal Router(config)# interface eth0 Router(config-if)# ip address 10.0.0.1/8 Router(config-if)# ^Z Router# VTY Modes --------- There are three basic VTY modes: There are commands that may be restricted to specific VTY modes. VTY View Mode ~~~~~~~~~~~~~ This mode is for read-only access to the CLI. One may exit the mode by leaving the system, or by entering *enable* mode. VTY Enable Mode ~~~~~~~~~~~~~~~ This mode is for read-write access to the CLI. One may exit the mode by leaving the system, or by escaping to view mode. VTY Other Modes ~~~~~~~~~~~~~~~ This page is for describing other modes. VTY CLI Commands ---------------- Commands that you may use at the command-line are described in the following three subsubsections. CLI Movement Commands ~~~~~~~~~~~~~~~~~~~~~ These commands are used for moving the CLI cursor. The "C" character means press the Control Key. "C-f" / "LEFT" Move forward one character. "C-b" / "RIGHT" Move backward one character. "M-f" Move forward one word. "M-b" Move backward one word. "C-a" Move to the beginning of the line. "C-e" Move to the end of the line. CLI Editing Commands ~~~~~~~~~~~~~~~~~~~~ These commands are used for editing text on a line. The "C" character means press the Control Key. "C-h" / "DEL" Delete the character before point. "C-d" Delete the character after point. "M-d" Forward kill word. "C-w" Backward kill word. "C-k" Kill to the end of the line. "C-u" Kill line from the beginning, erasing input. "C-t" Transpose character. CLI Advanced Commands ~~~~~~~~~~~~~~~~~~~~~ There are several additional CLI commands for command line completions, insta-help, and VTY session management. "C-c" Interrupt current input and moves to the next line. "C-z" End current configuration session and move to top node. "C-n" / "DOWN" Move down to next line in the history buffer. "C-p" / "UP" Move up to previous line in the history buffer. "TAB" Use command line completion by typing "TAB". "?" You can use command line help by typing "help" at the beginning of the line. Typing "?" at any point in the line will show possible completions. Pipe Actions ~~~~~~~~~~~~ VTY supports optional modifiers at the end of commands that perform postprocessing on command output or modify the action of commands. These do not show up in the "?" or "TAB" suggestion lists. "... | include REGEX" Filters the output of the preceding command, including only lines which match the POSIX Extended Regular Expression "REGEX". Do not put the regex in quotes. Examples: frr# show ip bgp sum json | include remoteAs "remoteAs":0, "remoteAs":455, "remoteAs":99, frr# show run | include neigh.*[0-9]{2}\.0\.[2-4]\.[0-9]* neighbor 10.0.2.106 remote-as 99 neighbor 10.0.2.107 remote-as 99 neighbor 10.0.2.108 remote-as 99 neighbor 10.0.2.109 remote-as 99 neighbor 10.0.2.110 remote-as 99 neighbor 10.0.3.111 remote-as 111